single-point fixings for interior installations

SINGLE-POINT FIXINGS FOR INTEROIR INSTALLATIONS
SINGLE-POINT
FIXINGS
FOR INTERIOR
INSTALLATIONS
—
MANET
CONTENT
—
MANET CONCEPT
Sliding door system
6 – 21
Pivoting door system 22 – 35
36 – 43
Connection system Single-point fixings
44 – 49
MANET COMPACT Sets
Pivoting doors
Sliding doors
53 – 55
56 – 61
62 – 71
Pull Handles and
recessed pull grip program
The glass preparation requirements for the various systems are indicated at the end of each section.
ManET GlasS DESIGN SYSTEM
MANET – the SYSTEM
—
Glass assembly system
It’s good to be able to see clearly
if you want to plan ahead.
That also certainly applies when
it comes to designing office
layouts. As well as promoting
open communication, transparent
interior concepts are particularly
generous in appearance. And
here, adaptable partitioning and
doors of glass certainly help.
Offering a flexible modular
system, MANET gives planners
plenty of scope in room design.
The basic component is the
single-point fixing, fitting into
a countersunk hole to provide
a flush finish with the glass
surface – an optical highlight
common to all the hardware in
this range. Adjustable angle
4
DORMA
connectors ensure efficient
attachment to both the existing
building fabric and other glass
elements. Integrated swing and
sliding door sets, the latter in
two design versions, complete
the system. For some components, both countersunk and
proud single-point fixings are
available. Swing door fittings
that attach to sidelights and
overpanels can be had for glass
thicknesses ranging from 10 to
15.5 mm. The fixings for sliding
doors are designed as standard
for glass panel thicknesses from
8 to 17.5 mm. Further glass
thicknesses are also available
on request, as is the installation
of 20 – 40 mm thick timber
door leaves.
Compact Sets
Equally effective visually is the
MANET COMPACT system with
its standardized swing and sliding door sets. These enable
simple, fast configuration of
common installation types with
8, 10 or 12 mm glass for doors
and 10 and 12 mm glass for
overpanels and sidelights, aided
by MANET COMPACT planning
software. MANET COMPACT sliding door sets come with roller
carriers featuring the straight
lines of our CLASSIC design.
A wide range of accessories
ensures that the individual sets
can be adapted to an array of
application types, with MANET
pull handles completing the
holistic, integral appearance.
To enable problem-free installation of sliding, double-action and
single-action doors, the system
components all offer extensive
adjustability. Wall abutment
profiles may, however, need to
be provided by others for fixing
glass overpanels and sidelights.
ManET GlasS DESIGN SYSTEM
MANET CONCEPT
Single-point
fixing
Connection
system
MANET COMPACT
Pivoting door
fittings
Sliding door
fittings
Pivoting door
sets
Sliding door
sets
TSG
TSG
Applications and features
Glass
TSG
TSG
TSG
TSG
LSG from TSG LSG from TSG LSG from TSG LSG from TSG
For interior assemblies
3
3
Max. door weight (kg)
3
3
3
3
100
120
80
100
Max. door width (mm)
1200
1500
1200
1200
Max. door height
3000
3000
2500
2500
3
3
3
3
3
3
Masonry openings
3
For standard toughened glass assembly types
3
3
3
For individual designed assemblies
3
3
3
Double action door
3
3
Single action door
3
3
Sliding door
3
1-panelled doors
3
2-panelled doors
Glass thicknesses door (mm)
Glass thicknesses overpanel / sidelight
8 – 17.5
8 – 21.5
3
3
3
3
3
3
3
3
10 – 15.5
8 – 17.5
10, 12
8, 10, 12
10 – 15.5
10 – 17.5
10, 12
10, 12
Timber thicknesses sliding door (mm)
20 – 40
Installation and adjustability
Installation at wall
3
3
3
3
3
Installation at ceiling
3
3
3
3
Installation at glass
3
3
3
3
3
3
3
3
3
3
Roller at glass
2-D / 3-D adjustable
31)
3
3
3
Installation and adjustability
Satin stainless steel 1.4305
3
3
3
3
Satin stainless steel 1.4404
on request
on request
on request
on request
TREND
3
CLASSIC
3
Roller at glass
3
3
Glass preparation
countersunk single-point fixings
3
3
3
3
clamping disc single-point fixings
3
3
3
3
1) Max.
3
3
3
panel weight 80 kg
All elements including the pull
handles are supplied in an
elegant stainless steel finish.
MANET components come in
the steel grade 1.4305 (AISI
303) for normal interior applications. Certain selected fittings
are also available in 1.4404
(AISI 316L) for damp room
and external applications (not
suitable saunas or indoor
swimming pools). The materials
necessary for your application
can be determined from Table 1
of General Building Inspectorate
Approval Z-30.3-6 .
Note: The products detailed in
this brochure are exclusively
intended for glass constructions
that do not require special individual inspectorate approval.
Awarded with the design prize
red dot 2002
DORMA
5
MANET CONCEPT
—
Sliding door system
6 – 21
6
DORMA
DORMA
7
manet CONCEPT
SlIDING DOOR SYSTEM
—
The MANET sliding door system
is ideal as an elegant addition
complementing high-style
interior concepts. Its main components take the form of a solid
track rail and the roller carrier.
Whether you prefer the TREND
or CLASSIC versions, both can
be combined with the solid
track or a tubular track. The
range includes both glass-flush
and proud single-point fixings.
The sliding door system allows
plenty of scope for individual
ideas.
In addition to the standard versions incorporated in toughened
glass partitions or face-fixed on
masonry openings, this hardware system can also be used to
construct curved sliding doors,
biparting sliding doors and parallel sliding doors.
The fittings are designed for a
door weight of max. 120 kg,
resp. 80 kg with roller to glass.
Mechanical stops that can be
positioned on the track rail
ensure that the door travel distance is effectively limited.
Roller carrier TREND
Roller carrier CLASSIC
Glass connection with drilled solid tracks
Roller carrier TREND
Glass connection with clamp fixing and tubular tracks
8
DORMA
Roller carrier CLASSIC
An accordant anti-jump device
for solid and tubular tracks will
be used.
manet CONCEPT
Roller carrier TREND
incl. anti-jump device
only lug with roller
Art. No. 29.424
Roller carrier CLASSIC
incl. anti-jump device
only lug with roller
Art. No. 29.422
AISI 316L
Art. No. 29.423
Single-point fixing
for roller carrier, 2 pcs. each
countersunk 8 – 12 mm glass
Art. No. 29.430
AISI 316L
Art. No. 29.431
clamping disc 8 – 12 mm glass
Art. No. 29.432
AISI 316L
Art. No. 29.433
countersunk for
13.5 – 17.5 mm glass
Art. No. 29.435
countersunk for 19 mm glass
Art. No. 29.437
Single-point fixings
for roller carrier at timber,
2 pcs. each
countersunk for 20 – 40 mm
timber
Art. No. 29.510
clamping disc for 20 – 40 mm
timber
Art. No. 29.520
55
205
55
55
205
55
rolleR CARRIER
—
DORMA
9
manet CONCEPT
SOLID TRACk
—
Track supply and installation
The track rail for the sliding
door is pre-fabricated according
to the customer’s drawing and
supplied together with the glass
or wall brackets ordered for the
application concerned.
Fixing screws for wall
installation by others
Of decisive importance for prefabrication and fixing to glass
partitions is that the mounting
points coincide with the holes
drilled in the glass. The lengthwise tolerances should not be
greater than ± 0.3 mm.
Caution! Ensure that the stops/single-point fixings are positioned at
locations appropriate to the width of the door.
Wall/single-point fixing
clearance when using
the wallconnector
(depends on stopper
position).
For rail support intervals on
the glass wall or masonry,
see fixing point interval
recommendations per the
table.
Required dimensions for the track production
G = Fixing point at glass
W = Fixing point at wall
K = Connection
WK= Angle-connection
G
G
see table
W
W
50
3
see table
100
Track length
G
G
G
G
K*
100
see table
100
max. 5000 with connector
G
see table
max. 5000 with connector
* Note! Ensure that track joints and glass joints do not coincide
min. 80
G
G
G
G
38
min. 80
3
18
38
WK
see table
see table
see table
max. 5000 with angle-connector
18
Recommended distance of the track fixing points
Door
height
in mm
1900
2000
2100
2200
2300
2400
2500
10
700
Glass thickn. mm
8 10 12
770 710 670
750 700 650
730 680 640
710 660 620
690 640 610
680 630 590
660 610 580
DORMA
800
Glass thickn. mm
8 10 12
770 720 670
750 700 660
730 680 640
710 660 620
700 650 610
680 630 590
670 620 580
900
Glass thickn. mm
8 10 12
770 710 670
750 700 650
730 680 640
710 660 620
700 640 610
680 630 590
670 610 580
Door width in mm
1000
1100
Glass thickn. mm Glass thickn. mm
8 10 12 8 10 12
760 710 670 760 700 660
740 690 650 740 680 640
730 670 630 720 670 630
710 660 620 700 650 610
690 640 600 690 640 600
680 630 590 670 620 590
660 620 580 660 610 580
1200
Glass thickn. mm
8 10 12
750 700 650
730 680 640
710 660 620
700 650 610
680 630 600
670 620 580
650 610 570
1300
Glass thickn. mm
8 10 12
740 690 650
720 670 630
710 660 620
690 640 600
680 630 590
660 610 580
650 600 570
1400
Glass thickn. mm
8 10 12
730 680 640
720 660 630
700 650 610
680 630 600
670 620 580
660 610 –
640 600 –
manet CONCEPT
SOLID TRACK and accessories
—
Solid track
The track rail is prefabricated
per customer specifications/
drawing with all the necessary
drill holes already provided.
ø 25
up to 6000 mm*
*max. single length 5000 mm
by coupling
Art. No. 21.405
AISI 316L
Art. No. 21.456
for fixing at wall
up to 6000 mm
Art. No. 21.406
AISI 316L
Art. No. 21.457
Track, undrilled
for fixing with clamp brackets
fixed length up to 6000 mm
Art. No. 21.407
do. AISI 316L
Art. No. 21.458
Connectors
offset for tracks 90 – 180°
Art. No. 21.442
do. AISI 316L
Art. No. 21.443
Door stop
left hand
Art. No. 29.425
AISI 316L
Art. No. 29.427
right hand
Art. No. 29.426
AISI 316L
Art. No. 29.428
Wall fixing for tubular track /
solid track
Art. No. 29.445
AISI 316L
Art. No. 29.446
38
Threaded rod
M5 x 6
Track, drilled
for fixing at glass
fixed length up to 6000 mm
Angle
connection
90 – 180°
38
right
hand
ø 25
ø 35
left
hand
56
20
DORMA
11
manet CONCEPT
SOLID TRACK and accessories
—
Solid track fixing at wall
Art. No. 21.346
AISI 316L
Art. No. 21.347
Flange for fixing the track
at wall, adjustable
Adjustment + 5 mm
Note: Min. distance
glass to wall 32 mm
Art. No. 21.412
Fixing for double track
Art. No. 21.170
ø 25
Flange for fixing the track
at wall
18
Solid track fixing at wall, adjustable
ø 25
ø 55
2-dimensional adjustment
via oblong hole
35
Fixing a double track
10/12
60
ø 20
18
Solid track fixing at ceiling
Ceiling retainer for track
ø 65
110
ø 25
29
12
DORMA
carrying function
ø 25
Art. No. 21.315
manet CONCEPT
Single-point fixing for solid track fixing at glass
for X = 20 – 30 mm
Single-point fixing,
ø 25
Glass thickness
18
countersunk, fixed
for 10/12 mm glass
Art. No. 29.460
AISI 316L
Art. No. 29.461
for 13.5 – 15.5 mm glass
Art. No. 29.450
for 17.5 mm glass
Art. No. 29.451
clamping disc, fixed
for 10/12 mm glass
Art. No. 29.465
AISI 316L
Art. No. 29.466
countersunk, centring
for 10/12 mm glass
Art. No. 29.462
AISI 316L
Art. No. 29.463
for 13.5 – 15.5 mm glass
Art. No. 29.455
for 17.5 mm glass
Art. No. 29.456
clamping disc, centring
for 10/12 mm glass
Art. No. 29.467
AISI 316L
Art. No. 29.468
for X = 35 – 40 mm
Single-point fixing,
ø 25
Glass thickness
countersunk, fixed
for 10/12 mm glass
Art. No. 29.530
countersunk, centring
for 10/12 mm glass
Art. No. 29.531
35
Selection guide, Solid track fixing for timber doors
mm
mm
28
Z
max.
door weight
kg
Single-point fixing
fixed for track
Art. No.
countersunk
35
28
X
35
Single-point fixing
centring for track
Art. No.
Flange for
track
Art. No.
clamping countersunk clamping
disc
disc
18.5
120
29.460
29.465
29.462
29.467
21.346
35 – 40
35
100
29.530
–
29.531
–
21.412
55
15
X
37
20 – 30
60
55
37
60
15
X
to wall
to glass 10/12 mm
Z
Z
Glass thickness
Height adjustment –2,5
DORMA
13
manet CONCEPT
TUBULAR TRACKS AND ACCESSORIES
—
Recommended distance of the track fixing points
see table
Door
height
in mm
1900
2000
2100
2200
2300
2400
2500
700
Glass thickn. mm
8 10 12
350 350 350
350 350 350
350 350 350
350 350 350
350 350 350
350 350 350
350 350 350
800
Glass thickn. mm
8 10 12
400 400 400
400 400 400
400 400 400
400 400 400
400 400 400
400 400 400
400 400 400
900
Glass thickn. mm
8 10 12
450 450 450
450 450 450
450 450 450
450 450 450
450 450 450
450 450 450
450 450 450
Door width in mm
1000
1100
Glass thickn. mm Glass thickn. mm
8 10 12 8 10 12
500 500 500 550 550 530
500 500 500 550 540 510
500 500 500 550 530 500
500 500 500 550 520 490
500 500 500 550 510 480
500 500 500 530 500 470
500 500 500 520 490 460
ø 25
3000 mm / 6000 mm
1300
Glass thickn. mm
8 10 12
590 550 510
570 530 500
560 520 490
550 510 480
540 500 470
530 490 460
520 480 450
Tubular track
incl. end plugs
stock length 3000 mm
Art. No. 21.527
AISI 316L
Art. No. 21.530
Fixed length up to 6000 mm
Art. No. 21.436
AISI 316L
Art. No. 21.532
Tubular track
bent, incl. end plugs
max. curve length 2600 mm
Art. No. 21.409
max. curve length 5600 mm
Art. No. 21.413
Angled connection for
tubular track, 90° – 180°
Art. No. 21.535
Angle connection
for tubular track
Art. No. 29.506
Thread insert
for tubular track
Art. No. 29.505
r=
min
. 60
0m
m
Curve length
1200
Glass thickn. mm
8 10 12
600 550 520
580 540 510
570 530 500
550 510 480
540 500 470
530 490 460
520 480 450
38
Threaded rod
M5 x 6
Angle
connection
90 – 180°
ø 21
38
ø 21
40
40
14
DORMA
40
1400
Glass thickn. mm
8 10 12
580 540 510
570 530 500
560 520 490
540 500 470
530 490 460
520 480 –
510 470 –
manet CONCEPT
Tubular track fixing at glass
Glass
thickness
ø 25
18
Glass
thickness
ø 25
Clamp fixing
for tubular track at glass
single-point fixing countersunk*
Art. No. 29.176
AISI 316L
Art. No. 29.185
single-point fixing, clamping disc*
Art. No. 29.177
AISI 316L
Art. No. 29.186
16 mm extended
single-point fixing countersunk*
Art. No. 29.179
single-point fixing, clamping disc*
Art. No. 29.180
*for 10, 12 and 13.5 mm glass
35
Tubular track fixing at wall
ø 25
Clamp fixing
for tubular track at wall
Art. No. 29.175
AISI 316L
Art. No. 29.184
Clamp fixing
for tubular track at wall
16 mm extended
Art. No. 29.178
AISI 316L
Art. No. 29.187
18
ø 25
35
Selection guide, tubular track fixing for timber doors
Z
X
Z
mm
mm
max.
door weight
kg
to wall
Clamp fixing
for track
Art. No.
Clamp fixing
for track
Art. No.
countersunk
clamping disc
20 – 30
18.5
120
29.175
29.176
29.177
35 – 40
35
100
29.178
29.179
29.180
37
55
15
X
55
X
37
60
35
35
28
28
Glass thickness
to glass
Height adjustment –2.5
DORMA
15
manet CONCEPT
TUBULAR TRACK AND ACCESSORIES
—
right hand
Door stop
left hand
Art. No. 29.425
AISI 316L
Art. No. 29.427
right hand
Art. No. 29.426
AISI 316L
Art. No. 29.428
Wall fixing for tubular track /
solid track
Art. No. 29.445
AISI 316L
Art. No. 29.446
Ceiling retainer
for tubular track,
carrying function
Art. No. 21.316
Ceiling retainer doubly
for tubular track,
carrying function
Art. No. 21.317
ø 25
ø 35
left hand
56
20
Tubular track fixing at ceiling
110
ø 65
ø 25
ø 25
26
110
ø 65
ø 25
ø 25
26
16
DORMA
manet CONCEPT
70
Roller at glass
Roller at glass
for 8 – 12 mm glass,
countersunk
Art. No. 29.494
clamping disc
Art. No. 29.495
Door stop
for roller at glass,
left hand and right hand usable
Art. No. 29.493
AISI 316L
Art. No. 29.483
Anti-jump device
for roller at glass
for 8 – 12 mm glass,
countersunk
Art. No. 29.497
clamping disc
Art. No. 29.498
DORMA
17
manet CONCEPT
ACCESSORIES
—
Aluminium brush profile
similar satin stainless steel
for 8 mm glass
stock length 3000 mm
Art. No. 07.402
fixed length up to 6000 mm
Art. No. 07.403
for 10/12 mm glass
stock length 3000 mm
Art. No. 07.400
fixed length up to 6000 mm
Art. No. 07.401
15.5 for 8 mm glass
13.5 for 10 mm glass
11.5 for 12 mm glass
Sliding door lock with
ratchet brace
Art. No. 21.446
ø 38
ø 48
75
38
for 8/10/12 mm glass
AISI 316L
14
15
30
15
Guide rail with brush seals
applicable for
8/10/12 mm glass
24
10
24
30
55
18
DORMA
aluminium mill finished
fixed length up to 6000 mm
Art. No. 21.431
stock length 3000 mm
Art. No. 21.432
Floor guide
clamping disc,
applicable for
8/13.5 mm glass
Art. No. 07.316
aluminium 113
(similar satin stainless steel)
Art. No. 07.316
manet CONCEPT
Corner lock
for 8 – 12 mm glass,
Art. No. 21.448
Corner lock
with profile cylinder rose
on inside
for 8 – 12 mm glass
Art. No. 21.449
Dead lock for KABA
with rose on inside
for 8 – 12 mm glass
Art. No. 21.450
Profile cylinder
for corner lock
Art. No. 14.206
Eccentric bushing
for corner lock
Art. No. 05.194
Bushing,
plastics
Art. No. 00.110
Strike plate
Art. No. 05.190
Door steady,
to prevent glass edges of
bi-parting double sliding doors
Art. No. 29.420
Glass thickness
12
65
21
ø 55
7
7
65
65
113
ø 55
73
Floor
Floor
3
28
ø 40
Floor
ø 25
32
ø 16
94
50
Please order for details for glass
preparations our detail sheet
29-044-B.
6
10 (8, 12)
35
DORMA
19
1
R1
manet CONCEPT
GLASS PREPARATION FOR SLIDING DOOR SYSTEM
—
Sliding door to wall
Detail A
Wall
Detail B
Sliding door
Wall
Sliding door with sidelight and overpanel
Overpanel
Detail C
Wall
Detail D
Sliding door
Sidelight
Sliding door with two sidelights and overpanel
Overpanel
Detail E
Sidelight
20
DORMA
Detail D
Sliding door
Sidelight
manet CONCEPT
Detail A
Sliding door
with solid track
Detail B
143
40
40
40
40
28
143
50
143
55
143
60
35
28
18
Sliding door with tubular track
and clamp fixing
Detail D
3
50
50
18
50
143
143
143
40
40
glass edge protection
on site
Detail E
3
50
100
Countersunk
bore for
countersunk
single-point
fixings
Cylindrical
bore for
clamping
disc singlepoint fixings
50
3
50
–0,2
90°
ø 22
143
+0,2
3
ø 32
Dimensional data should be
regarded exclusively as recommended values.
Please remember when
designing your system that the
positions of the stops and point
fixings must not vertically
coincide.
For spacing/interval recommendations when drilling the track
holes, and for requisite dimensions for fixing the track rail,
please refer to the table entitled
“Recommended distance of the
track fixing points”.
ø 26
143
55
50
28
60
35
50
3
28
Detail C
143
40
40
Glass
thickness
Glass
thickness
DORMA
21
MANET CONCEPT
—
Pivoting door system
22 – 35
22
DORMA
DORMA
23
manet CONCEPT
PIVOTING DOOR SYSTEM
—
MANET pivoting doors can be
installed in both glass partitions
and masonry openings. They
come as both single and doubleaction swing doors with a
maximum weight of 100 kg
and a maximum leaf width of
1200 mm.
All the single-point fixings are
designed for clip-on covers for
easier installation. Other components include the bottom
pivot bearing, top pivot fittings
with bearing spigot or eccentric
bushing and also overpanel/
sidelight connectors.
As a result, there are almost
unlimited possibilities for integrating frameless swing doors
both in masonry openings – with
or without overpanels and sidelights – and in glass partition
constructions retained by singlepoint fixings.
Whether with a full-length pivot
rod or a pair of shorter pivot
rods, the top bearing socket is
located in the fitting on the door
leaf. This means that connection
to the ceiling, lintel or transom
can now be provided in the form
of the standard PT25 top pivot
spigot from the DORMA range.
The door assemblies can be
equipped with floor springs such
as the DORMA BTS 75V or
BTS 84, and corner locks are
naturally also available.
Pivot bearing with
full-length pivot rod,
max. door panel height 3000 mm
Pivot bearing with
pivot rod pair short type,
max. door panel height 2500 mm
Pivot bearing with
pivot rod pair short type with
intermediate tube,
max. door panel height 2500 mm
Adjustment
+ 2.5
Bottom
pivot bearing
Pivot pole
24
DORMA
Zero position
Adjustment
+ 2.5
manet CONCEPT
COMPONENTS FOR PIVOTING DOOR SYSTEM
—
Overpanel / sidelight
connector
complete fitting
for 10/12 mm glass
countersunk
Art. No. 29.330
AISI 316L
Art. No. 29.362
clamping disc
Art. No. 29.356
Pivot bearing for overpanel
and ceiling connection
Art. No. 21.310
AISI 316L
Art. No. 21.350
Pivot bearing
for DORMA BTS (max. 4 EN) /
floor pivot
Art. No. 29.545
AISI 316L
Art. No. 29.550
115
Glass
thickness
18
76
76
18
18
DORMA
25
manet CONCEPT
COMPONENTS FOR PIVOTING DOOR SYSTEM
—
Pivot rod,
drilled, fixed length
18
Art. No. 29.551
Single-point fixing,
countersunk, fixed (1)
ø 32
83
2
for 10/12 mm glass
Art. No. 29.460
AISI 316L
Art. No. 29.461
for 13.5 – 15.5 mm glass
Art. No. 29.450
clamping disc, fixed (1)
2
ø 25
for 10/12 mm glass
Art. No. 29.465
AISI 316L
Art. No. 29.466
Single-point fixing,
countersunk, centring (2)
ø 32
2
for 10/12 mm glass
Art. No. 29.462
AISI 316L
Art. No. 29.463
for 13.5 – 15.5 mm glass
Art. No. 29.455
1
89
clamping disc, centring (2)
for 10/12 mm glass
Art. No. 29.467
Pivot rod set, short type
top/bottom,
incl. 4 single-point fixings
countersunk
Art. No. 29.546
AISI 316L
Art. No. 29.547
clamping disc
Art. No. 29.560
AISI 316L
Art. No. 29.561
Glass
thickness
26
DORMA
manet CONCEPT
countersunk
Art. No. 29.548
AISI 316L
Art. No. 29.549
clamping disc
Art. No. 29.562
AISI 316L
Art. No. 29.563
Intermediate tube
fixed length up to 2000 mm
Art. No. 29.555
AISI 316L
Art. No. 29.557
Pivot bearing for humid rooms
AISI 316L
Art. No. 29.540
Floor pivot
Art. No. 01.106
76
intermediate tube
Pivot rod set, short type
top / bottom,
for intermediate tube,
inclusive 4 single-point fixings
32
18
15
92
DORMA
27
manet CONCEPT
COMPONENTS FOR PIVOTING DOOR SYSTEM
—
Wall fixing
74
74
Overpanel / sidelight
connector for wall fixing
90° offset,
with pivot bearing location,
complete fitting
for 10/12 mm glass
70
70
3
right hand
Art. No. 29.328
left hand
Art. No. 29.329
120
3
120
18
18
70
70
3
right hand
Art. No. 29.326
left hand
Art. No. 29.327
120
120
3
74
74
Overpanel / sidelight
connector for wall fixing
90° offset,
complete fitting
for 10/12 mm glass
28
DORMA
manet CONCEPT
Glass fixing
73
Overpanel / sidelight
connector for glass fixing
90° offset,
with pivot bearing location,
complete fitting
for 10/12 mm glass
70
Glass
thickness
right hand
Art. No. 29.331
115
120
3
18
73
Overpanel / sidelight
connector for glass fixing
90° offset,
with pivot bearing location,
complete fitting
for 10/12 mm glass
70
3
left hand
Art. No. 29.332
Overpanel / sidelight
connection
for 10/12 mm glass,
countersunk
Art. No. 29.320
clamping disc
Art. No. 29.357
115
120
Glass
thickness
18
3
40
120
Glass
thickness
DORMA
29
manet CONCEPT
COMPONENTS FOR PIVOTING DOOR SYSTEM
—
Pivot bearing fitting
for overpanel with
cylindrical bore for rod
for 8 – 12 mm glass,
countersunk
Art. No. 29.354
Pivot bearing location
for overpanel
for 8 – 12 mm glass,
countersunk
Art. No. 29.333
AISI 316L
Art. No. 29.353
Pivot bearing for RTS
Art. No. 29.314
Pivot pole, drilled,
fixed length, for RTS
pivot bearing 29.314
Art. No. 29.553
PT 25 pin
for ceiling connection,
15 mm Ø, with plug
Art. No. 01.115
ø
25
60
115
Glass thickness
18
115
Glass thickness
18
76
3
46
105
Glass
thickness
M8
40
M8
40
40
40
40
M8
40
40
M8
M8
M8
76
18
30
M8
DORMA
Pivot bearing for
installation to ceiling
adjustable
for 8 – 12 mm glass,
AISI 316L
Art. No. 21.319
Art. No. 21.318
manet CONCEPT
ACCESSORIES
—
39
Stop for pivoting door
with ceiling mounting
Art. No. 21.334
Stop at overpanel
(inside/outside)
for 10/12 mm glass,
Art. No. 29.335
Overpanel / sidelight
connection
with stop inside
for 10/12 mm glass,
countersunk
Art. No. 29.322
Overpanel / sidelight
connection
with stop outside
for 10/12 mm glass,
countersunk
Art. No. 29.325
40
Ceiling
30
Glass
thickness
3
40
120
Glass
thickness
40
120
Glass
thickness
3
30
40
73
5
DORMA
31
manet CONCEPT
ACCESSORIES
—
Wall
Stop for pivoting door
floor mounting
Art. No. 29.950
Stop for pivoting door
wall mounting, short
Art. No. 29.951
Stop for pivoting door
wall mounting, long
Art. No. 29.952
24
Glass
40
ø 20
Glass
Wall
31
ø 20
Glass
32
DORMA
Floor
Wall
94
manet CONCEPT
Corner lock
for 8 – 12 mm glass,
Art. No. 21.448
Corner lock
with profile cylinder rose on
inside for 8 – 12 mm glass
Art. No. 21.449
Dead lock for KABA
with rose on inside
for 8 – 12 mm glass
Art. No. 21.450
Profile cylinder
for corner lock
Art. No. 14.206
Eccentric bushing
for corner lock
Art. No. 05.194
Bushing,
plastics
Art. No. 00.110
Strike plate
Art. No. 05.190
Glass thickness
12
65
21
ø 55
7
7
65
65
113
ø 55
73
Floor
Floor
3
28
ø 40
Floor
ø 25
32
ø 16
94
DORMA
33
manet CONCEPT
GLASS PREPARATION FOR PIVOTING DOOR SYSTEM
—
Countersunk holes
Glass thickness
The gap and distance dimensions
recommended by DORMA are
indicated in the adjacent table.
Glass thickness
mm
13.5–15.5
ø 26
ø 32+0,2
90°
10/12
Connection
X
Gap
Sidelight
5
Wall
8
Sidelight
8
Wall
11
Y
65
62
3–0,2
Detail A
at sidelight
Detail A
at wall
113
113
3
3
Detail A
X
X
Y
Detail B
at wall
Detail B
Y
Detail C
at wall
Detail B
at glass wall
3
3
3
70
70
70
Y
DORMA
120
120
X
34
40
3
40
3
113
3
50
113
40
160
Detail C
X
Y
manet CONCEPT
Detail D
50
67
3
3
40
50
120
Detail D
113
Detail E
Y
7
113
24
89
X1 ± 0,3
X1 ± 0,3
X3 ± 0,3
X
18
Y
Glass
Detail E
Detail E
with stop
3
50
120
3
40
67
3
120
3
40
Detail E
3
Detail B
BTS
67
50
3
DORMA
35
MANET CONCEPT
—
Connection system
36 – 43
36
DORMA
DORMA
37
manet CONCEPT
CONNECTION SYSTEM
—
The system approach is very
much in evidence in the case of
the interconnecting components.
Elements such as clamping and
angle connectors of various
designs and also interconnecting
fasteners of various lengths can
be combined in order to attach
glass of different thicknesses at
any required angle to the floor,
to ceilings, to walls and to plinth
supports.
Single-point fixings flush with
the glass are also used for this
interconnection and glass-toglass system. Tolerances are
compensated by sloted holes in
the interconnecting fasteners.
Glass fixing
Components
7
8
2
1
3
 1Clip-on cover
 2Connecting bolt
 3Conical collar
 4Conical sleeve
 5Gasket
 6Pivoting clamp
 7Connecting bolt
 8Connecting rod to suit
length
6
4
5
Wall fixing
Components
9
10
11
12
13
8
90° – 180° Glass / Glass
38
DORMA
Glass / Glass Connector
 9Connecting bolt
10 Pivoting clamp
11Threaded rod M8 with small
head, Length and type to
suit wallplug
12Mounting plate,
2-dimensional adjustment
13Wallplug on site to suit wall
construction
90° – 180° Glass / Wall
manet CONCEPT
CLAMP CONNECTION GLASS
—
Components
1
Connecting rod or steel
cable
2 Connecting bolt
3 Pivoting clamp
4 Connecting bolt
5 Gasket
6 Pivoting clamp
2
6
3
5
1
4
5
CONNECTION CEILING / FLOOR
—
Components
7
8
7 Wallplug on site
8
Mounting plate,
2-dimensional adjustable
9
Threaded rod M8
10Column
9
10
Ceiling suspension only permissible with bottom glass panel support.
ALTERNATIVE CONNECTION CEILING
—
Components
Single-point fixing
clamping disc
12
Single-point fixing
countersunk
Threaded rod M8
11
DIN 7984 M10 x..., or
oval-head wood screw
DIN 7996 M8 x...
12Clip-on cover
11
DORMA
39
manet CONCEPT
COMPLETE FITTING
—
Complete fitting glass / glass
for 8 – 12 mm glass thickness
ø 20
ø 36
ø 32
Glass / Glass 90° – 180°
28
Connecting rod
52.5 / 60 / 82 / 103 mm
Glass thickness
Art. No. 29.120
With connecting rod 60 mm
Art. No. 29.122
With connecting rod 82 mm
Art. No. 29.125
With connecting rod 103 mm
Art. No. 29.130
Complete fitting glass / wall
for 8 – 12 mm glass thickness
ø 36
ø 20
Glass / Wall 90° – 180°
Connecting rod
52.5 / 60 / 82 mm
32
With connecting rod 52.5 mm
Art. No. 29.139
With connecting rod 60 mm
Art. No. 29.140
With connecting rod 82 mm
Art. No. 29.142
Complete fitting
Connector
for glass thickness 8 – 12 mm
Glass / Glass 180° fixed
ø 32
Glass thickness
Glass thickness
With connecting rod 52.5 mm
AISI 303
Art. No. 29.148
AISI 316L
Art. No. 29.368
120
3
ø 36
ø 20
Complete fitting
Clamping connector
28
for glass thickness 8 – 12 mm
Art. No. 29.149
28
Complete fitting
Corner connector 90°
Glass/Floor
Glass/Ceiling
for glass thickness 8 – 12 mm
(only bearing function)
Complete fitting
Ceiling fixing
(bearing function)
for glass thickness 8 – 12 mm
countersunk
Height
adjustment
via grub screw
AISI 316L
Single-point fixing countersunk
40
DORMA
Single-point fixing clamping disc
clamping disc
AISI 316L
Art. No. 29.145
Art. No. 29.337
Art. No. 29.339
Art. No. 29.338
Art. No. 29.340
manet CONCEPT
COMPONENTS
—
Pivoting glass clamp
inclusive screw sets
for 8 – 12, 13.5 – 17.5 and
17.5 – 21.5 mm glass,
countersunk
Art. No. 29.160
do., clamping disc
Art. No. 29.165
Pivoting wall fixing
Art. No. 21.141
Column
Ceiling/floor fixing
Art. No. 21.146
Clamping connector
for Glass thickness 8 – 12 mm
Art. No. 29.149
Connecting rods
52 mm
82 mm
60 mm
103 mm
Length 52.5 mm
Art. No. 21.355
Length 60 mm
Art. No. 21.356
Length 82 mm
Art. No. 21.357
Length 103 mm
Art. No. 21.358
DORMA
41
manet CONCEPT
GLASs PREPARATION CONNECTION SYSTEM
—
For TSG and LSG from TSG.
Recommended centres for fixed glazing element
Countersunk bore for countersunk single-point fixings
90°
3 – 0,2
.
max. 800 ± 0.3
0.2
ø 32 + 0,2
Glass thickness
max. 800 ± 0.3
ø 26
ø 26 + 0.2
0,2
Glass thickness
± 0.3
Cylindrical bore for clamping disc single-point fixings
Corner connectors glass / glass (dimensions in mm)
Corner connectors glass / glass 90 – 180°
Length of
connecting rod
52,5
Con
nec
ting
ro
Ang
le
m
Di
°
en
si
on
A
Dimension B
3
d
d
Dimension B
3
28
ro
28
ct
in
g
90
Dimension A
Co
nn
e
DORMA
82
Angle
A/B
A/B
A/B
 90°
75
80
96
 95°
70
75
90
100°
66
71
85
105°
62
67
81
110°
59
63
77
73
115°
55
60
120°
52
56
69
125°
49
54
66
130°
47
51
63
135°
44
48
60
180°
42
60
103
Dimensions for 10 mm glass thickness
(consider variants
for other glass thicknesses).
A/B
50
manet CONCEPT
Clamping connector
60
ø 15
67
28
3
150
28
Corner connectors glass / wall 90 – 180°
Glass / wall (dimensions in mm)
Length of
connecting rod
28
ro
52,5
d
Wall
Dimension B
Corner connector glass / ceiling
Corner connector glass / floor
82
Angle
A/B
A/B
A/B
90°
67/65
72/70
87,5/86
Ceiling fixing (bearing)
28
Ceiling
60
Dimensions for 10 mm glass thickness
(consider variants for
other glass thicknesses).
32
3
ct
in
g
e
gl
An
Dimension A
Co
nn
e
Ceiling
65
75
72
72
75
5
42
3
KS
28
Floor
Glass
thickness
Vertically
adjustment ± 2.5
Note: Ensure compliance with minimum glass/bore clearances as per glass manufacturer recommendations.
Glass preparation with a tolerance of max. ± 0.3 mm is recommended.
DORMA
43
MANET CONCEPT
—
Single-point fixing
44 – 49
44
DORMA
DORMA
45
manet CONCEPT
SINGLE-POINT FIXING SERIEs S32/35
—
The basic component within the
MANET system is the singlepoint fixing. Rather than cylindrical bore in the glass, this has a
tapered countersunk bore for
a perfect seated fit to the glass.
These give a flush finish of the
single-point fixing in all applications.
46
DORMA
The three-dimensional adjustability incorporated within the
fitting ensures ideal compensation for structural and drilling
tolerances.
Constraint-free transmission of
all the forces acting on the
glass to the substructure is also
ensured.
manet CONCEPT
Simple installation and metric
adjustment
The fixing and the gasket are
wound onto the adjustment
screw already fitted to the wall,
with the glass panel then being
simply mounted over the top.
The adjustment screw allows
the position of the glass to be
adjusted in 3 dimensions.
An adjustment range of ±2 mm
in the vertical and lateral directions can be utilized by rotating
the adjustment screw by up to
90°. Then it is simply a matter
of aligning and securing the
single-point fixing and conical
sleeve. The clip-on cover
provides for a flush appearance.
Components
8
6
5
7
1 Clip-on cover
2 Pin internal thread
3 Conical sleeve
4Gasket
5Fixing
6Threaded rod M8 with
small head (eg DIN 6912).
Length and type to suit
wallplug
7 Adjustment screw
8Wallplug on site to suit wall
construction
4
2
3
1
DORMA
47
manet CONCEPT
ø 35
ø 32
ø 35
ø 32
ø 35
ø 32
ø 35
ø 32
TypeS
—
8.5 – 11.5 mm,
adjustable
11.5 – 14.5 mm,
adjustable
14.5 – 22 mm,
adjustable
6 mm,
not adjustable
Single-point fixing, glass / wall
wall offset 8.5 – 11.5 mm,
adjustable
Single-point fixing, glass / wall
wall offset 11.5 – 14.5 mm,
adjustable
Single-point fixing, glass / wall
wall offset 14.5 – 22 mm,
adjustable
Single-point fixing, glass / wall
fixed wall offset 6 mm,
not adjustable
Countersunk
8/10 mm glass
Art. No. 29.200
Countersunk
8/10 mm glass
Art. No. 29.201
Countersunk
8/10 mm glass
Art. No. 29.202
Countersunk
8/10 mm glass
Art. No. 29.205
12 mm glass
Art. No. 29.210
12 mm glass
Art. No. 29.211
12 mm glass
Art. No. 29.212
12 mm glass
Art. No. 29.215
13.5 mm glass
Art. No. 29.240
13.5 mm glass
Art. No. 29.241
13.5 mm glass
Art. No. 29.242
13.5 mm glass
Art. No. 29.243
15 mm glass
Art. No. 29.244
15 mm glass
Art. No. 29.245
15 mm glass
Art. No. 29.246
15 mm glass
Art. No. 29.247
17.5 mm glass
Art. No. 29.248
17.5 mm glass
Art. No. 29.249
17.5 mm glass
Art. No. 29.250
17.5 mm glass
Art. No. 29.251
Clamping disc
8/10 mm glass
Art. No. 29.700
Clamping disc
8/10 mm glass
Art. No. 29.701
Clamping disc
8/10 mm glass
Art. No. 29.702
Clamping disc
8/10 mm glass
Art. No. 29.730
12 mm glass
Art. No. 29.705
12 mm glass
Art. No. 29.706
12 mm glass
Art. No. 29.707
12 mm glass
Art. No. 29.731
13.5 mm glass
Art. No. 29.710
13.5 mm glass
Art. No. 29.711
13.5 mm glass
Art. No. 29.712
13.5 mm glass
Art. No. 29.732
15 mm glass
Art. No. 29.715
15 mm glass
Art. No. 29.716
15 mm glass
Art. No. 29.717
15 mm glass
Art. No. 29.733
17.5 mm glass
Art. No. 29.720
17.5 mm glass
Art. No. 29.721
17.5 mm glass
Art. No. 29.722
17.5 mm glass
Art. No. 29.734
Stainless steel quality AISI 316L on request.
48
DORMA
manet CONCEPT
GLASs PREPARATION CONNECTION SYSTEM
—
For TSG and LSG from TSG.
Recommended centres for fixed glazing element
± 0.3
max. 800 ± 0.3
max. 800 ± 0.3
Cylindrical bore for clamping disc single-point fixings
3 – 0,2
ø 32 + 0,2
Glass
thickness
90°
ø 26 + 0,2
Glass
thickness
Countersunk bore for countersunk single-point fixings
ø 26
DORMA
49
MANET COMPACT SETS
—
Pivoting doors
53 – 55
Sliding doors
56 – 61
50
DORMA
DORMA
51
manet COMPACT SETS
MANET COMPACT SETS
—
The aesthetic elegance of the
MANET COMPACT concept is
also available in the form of
standardised sets for simple,
fast planning of the more popular system types.
Optional accessories enable the
individual sets to be semi-customised.
The system components offer
numerous adjustment possibili-
ties in order to ensure problemfree installation of whichever
door type – sliding or swing,
single action or double action –
is required.
Wall abutment profiles may
need to be provided (by others)
for fixing overpanels and sidelights. (See technical brochure
”Fittings and door rails for
toughened glass assemblies”.)
Pivoting doors
Set 1
Page 53
Construction 1 (1 set)
Construction 2 (1 set)
Construction 3 (1 set)
Construction 4 (1 set)
Construction 5 (2 sets)
Construction 6 (2 sets)
Construction 7 (2 sets)
Construction 8 (2 sets)
Pivoting doors
with overpanel
Set 2
Pivoting doors
Set 2 + 3
Page 54/55
Page 54
Construction 9 (1 set)
Construction 12 (1 set)
Construction 18 (2 sets)
Pivoting doors
with overpanel
and sidelight
Set 3
Construction (1 Set each)
Page 55
Construction 13 (1 set)
Construction 15 (1 set)
Construction 23 (2 sets)
Sliding doors
Set 4/5/6
Page 56 – 61
Set 4.1/4.2
52
DORMA
Set 5.1/5.2
Set 6.1/6.2
manet COMPACT SETS
SET 1
—
113
Set 1
with single-point fixings countersunk
consisting of:
pivot rod pair top/bottom,
short type
Art. No. 29.910
150
3 Gap
Pivoting door MANET COMPACT without overpanel for 10 – 12 mm glass
Set 1
with pivot rod pair short type
Ceiling
65
including:
4 Single-point fixings for pivot rods
1 Pivot fitting top,
1PT 25 pin, 15 mm Ø, with plug
1Pivot fitting bottom
for DORMA BTS/floor pivot
Option:
Set 1, but for
additional intermediate tube in
fixed length for pivot rod pair
Intermediate tube in fixed length
Art. No. 29.911
Art. No. 29.555
Please indicate:
Panel height ____________________________________________ mm
– 577 mm
= Length intermediate tube
____________________________________________ mm
Gap
to sidelight 5
to wall 8
113
7 Gap
150
65
DORMA
BTS
Accessory options for Set 1
Pull handles
Pull handles
Door weight 80 kg
Door height max. 2500 mm
Door width max. 1200 mm
TSG 10/12 mm glass thickness
(single-point fixing countersunk)
Pair of pull handles
Length   350 mm
Art. No. 29.268
Length   720 mm
Art. No. 29.271
Length 1240 mm
Art. No. 29.274
Length 1760 mm
Art. No. 29.277
Length   350 mm
Art. No. 21.267
Length   720 mm
Art. No. 21.270
Length 1240 mm
Art. No. 21.273
Length 1760 mm
Art. No. 21.276
Lock
Corner lock
Art. No. 21.448
Corner lock with rose on one lock side
Art. No. 21.449
Profile cylinder for corner lock 21.448/449
Art. No. 14.206
Eccentric bushing for corner lock 21.448/449
Art. No. 05.194
Further accessories
Stop for pivoting door with ceiling mounting
Art. No. 21.334
Ceiling fixing (bearing function)
Art. No. 29.337
Floor pivot bearing
Art. No. 01.106
Assembling tool for MANET single-point fixings
Art. No. 21.134
For the requisite glass preparation please see pages 34 – 35
DORMA
53
manet COMPACT SETS
SET 2
—
Pivoting door MANET COMPACT with overpanel for 10 – 12 mm glass
Set 2
with pivot rod pair short type
Overpanel
150
3 Gap
113
Set 2
with single-point fixings countersunk
consisting of:
pivot rod pair top/bottom,
short type
Art. No. 29.912
including:
4 Single-point fixings for pivot rods,
1 Pivot fitting top,
1Pivot bearing location for overpanel,
1Pivot fitting bottom
for DORMA BTS/floor pivot
65
Wall
Option:
Set 2, but with
additional intermediate tube in
fixed length for pivot rod pair
Intermediate tube in fixed length
Art. No. 29.913
Art. No. 29.555
Please indicate:
Panel height ____________________________________________ mm
– 577 mm
= Length intermediate tube
____________________________________________ mm
Gap to wall 8
Accessory options for Set 2
Pull handles
DORMA
BTS
113
7 Gap
150
65
Door weight 80 kg
Door height max. 2500 mm
Door width max. 1200 mm
TSG 10/12 mm glass thickness
Pull handles
(single-point fixing countersunk)
Pair of pull handles
Length   350 mm
Art. No. 29.268
Length   720 mm
Art. No. 29.271
Length 1240 mm
Art. No. 29.274
Length 1760 mm
Art. No. 29.277
Length   350 mm
Art. No. 21.267
Length   720 mm
Art. No. 21.270
Length 1240 mm
Art. No. 21.273
Length 1760 mm
Art. No. 21.276
Ceiling fixing (bearing function)
Art. No. 29.337
Stop at overpanel, (inside/outside) for 10 and 12 mm glass
Art. No. 29.335
Lock
Corner lock
Art. No. 21.448
Corner lock with rose on one lock side
Art. No. 21.449
Profile cylinder for corner lock 21.448/449
Art. No. 14.206
Eccentric bushing for corner lock 21.448/449
Art. No. 05.194
Further accessories
Overpanel-sidelight connector for 10 and 12 mm glass
Art. No. 29.320
Overpanel-sidelight connector with stop inside for 10 and 12 mm glass
Art. No. 29.322
Overpanel-sidelight connector with stop outside for 10 and 12 mm glass
Art. No. 29.325
Floor pivot bearing
Art. No. 01.106
Assembling tool for MANET single-point fixings
Art. No. 21.134
For the requisite glass preparation please see pages 34 – 35
54
DORMA
manet COMPACT SETS
SET 3
—
Pivoting door MANET COMPACT with overpanel for 10 – 12 mm glass
Set 3
with pivot rod pair short type
3 Gap
113
Set 3
with single-point fixings countersunk
consisting of: pivot rod pair
top/bottom, short type
Art. No. 29.914
including:
4 Single-point fixings for pivot rods,
1 Pivot fitting top,
1Overpanel-sidelight connector
with pivot bearing location,
1Pivot fitting bottom
for DORMA BTS/floor pivot
150
3 Gap
Overpanel
65
Sidelight
Option:
Set 3, but with
additional intermediate tube in
fixed length for pivot rod pair
Intermediate tube in fixed length
Art. No. 29.914
Art. No. 29.555
Please indicate:
Panel height ____________________________________________ mm
– 577 mm
= Length intermediate tube
____________________________________________ mm
Gap to wall 8
65
Accessory options for Set 3
113
7 Gap
150
Pull handles
DORMA
BTS
Door weight 80 kg
Door height max. 2500 mm
Door width max. 1200 mm
TSG 10/12 mm glass thickness
Pull handles
(single-point fixing countersunk)
Pair of pull handles
Length   350 mm
Art. No. 29.268
Length   720 mm
Art. No. 29.271
Length 1240 mm
Art. No. 29.274
Length 1760 mm
Art. No. 29.277
Length   350 mm
Art. No. 21.267
Length   720 mm
Art. No. 21.270
Length 1240 mm
Art. No. 21.273
Length 1760 mm
Art. No. 21.276
Ceiling fixing (bearing function)
Art. No. 29.337
Stop at overpanel, (inside/outside) for 10 and 12 mm glass
Art. No. 29.335
Lock
Corner lock
Art. No. 21.448
Corner lock with rose on one lock side
Art. No. 21.449
Profile cylinder for corner lock 21.448/449
Art. No. 14.206
Eccentric bushing for corner lock 21.448/449
Art. No. 05.194
Further accessories
Overpanel-sidelight connector for 10 and 12 mm glass
Art. No. 29.320
Overpanel-sidelight connector with stop inside for 10 and 12 mm glass
Art. No. 29.322
Overpanel-sidelight connector with stop outside for 10 and 12 mm glass
Art. No. 29.325
Floor pivot bearing
Art. No. 01.106
Assembling tool for MANET single-point fixings
Art. No. 21.134
For the requisite glass preparation please see pages 34 – 35
DORMA
55
manet COMPACT SETS
SET 4.1/4.2
—
Sliding door MANET COMPACT for installation at wall, for 8 – 12 mm glass
Set 4.1
with single-point fixings
countersunk
Set 4.2
with clamping disc single-point
fixings
Fixed length: LL = 2 * TB – 170 mm
X
X
60
X
143
143
Door height max. 2500 mm
85
Door weight 80 kg
Door height max. 2500 mm
Door width max. 1200 mm
TSG 10/12 mm glass thickness
40
40
DBG = LM – 130 mm
LM
TB = LM + 80 mm
For the requisite glass preparation please see pages 20 – 21
56
DORMA
X
143
LM = Daylight opening
TB = Door width
DGB = Entry width
LL =Tubular track length
X
=Distance of single-point
fixings
(LM – 148) * 1/2
manet COMPACT SETS
Sliding door MANET COMPACT for installation at wall, for 8 – 12 mm glass
Set 4.1 / Set 4.2 consisting of: Set 4.1
with single-point fixings
countersunk
Set 4.2
with clamping disc single-point
fixings
5 Clamp fixings for track / wall
2Roller carriers CLASSIC
incl. single-point fixings for 8 – 12 mm glass
1 Door stop left hand
1 Door stop right hand
1 Floor guide AGILE
Installation tools
Art. No. 29.916
Art. No. 29.917
Set as above,
but with 16 mm extended clamp fixing
Art. No. 29.925
Art. No. 29.926
Not covered by the set:
Tubular track inclusive end cups in fixed length*
Art. No. 21.436
Art. No. 21.436
Tubular track, inclusive end cups,
stock length 3000 mm
Art. No. 21.527
Art. No. 21.527
Length   350 mm
Art. No. 29.268
Art. No. 21.240
Length   720 mm
Art. No. 29.271
Art. No. 21.241
Length 1240 mm
Art. No. 29.274
Art. No. 21.242
Length 1760 mm
Art. No. 29.277
Art. No. 21.243
Length   350 mm
Art. No. 21.267
Length   720 mm
Art. No. 21.270
Length 1240 mm
Art. No. 21.273
Length 1760 mm
Art. No. 21.276
for 8/10/12 mm glass
Art. No. 21.291
Accessory options for Set 4.1 / Set 4.2
Pull handles / Recessed pull grip
Pull handles
Pair of pull handles
Recessed pull grip Ø 60 mm
Recessed pull grip with grip hole Ø 60 mm
for 8 mm glass
Art. No. 21.292
for 10 mm glass
Art. No. 21.293
for 12 mm glass
Art. No. 21.294
Door knob back-to-back
for 8 – 12 mm glass
Art. No. 21.423
Door knob one side fixing
for 8 – 12 mm glass
Art. No. 21.422
Art. No. 21.426
Corner lock
Corner lock
Art. No. 21.448
Corner lock with rose on one lock side
Art. No. 29.449
Profile cylinder for corner lock 21.448/449
Art. No. 14.206
Eccentric bushing for corner lock 21.448/449
Art. No. 05.194
stock length 3000 mm
Art. No. 21.432
stock length 6000 mm
Art. No. 21.430
Art. No. 21.134
Further accessories
Aluminium guide rail with brush seals
Assembling tool for MANET single-point fixing
* When ordering please indicate the necessary length! For calculation please see adjoining page
DORMA
57
manet COMPACT SETS
SET 5.1/5.2
—
Sliding door MANET COMPACT for installation at glass, one side attached to masonry,
for sliding door 8 – 12 mm glass,
fixed element 10 – 12 mm glass
Set 5.1
with countersunk single-point
fixings
Set 5.2
with clamping disc single-point
fixing
Gap 3 mm
OB = LM – 3 mm
SB min. = LM – 60 mm
Fixed length: LL = 2 * TB – 160 mm
50
50
Overpanel
60
20
X
Sidelight
X
Y
Y
143
143
143
70
Door height max. 2500 mm
Sliding door
Door weight 100 kg
Door height max. 2500 mm
Door width max. 1200 mm
TSG 8/10/12 mm glass thickness
TSG 10/12 mm glass thickness
40
DBG = LM – 100 mm
LM
TB = LM + 40 mm
For the requisite glass preparation please see pages 20 – 21
58
DORMA
LM
=Daylight opening
TB
=Door width
DGB =Entry width
SBmin.= min. Seitenteilbreite
LL
=Tubular track length
X
=Centre distance
between single-point
fixings overpanel
(OB – 193) * 1/2
Y
=Centre distance
between single-point
fixings sidelight
Y = X – 29
OB =Overpanel width
manet COMPACT SETS
Sliding door MANET COMPACT for installation at glass, one side attached to masonry,
for sliding door 8 – 12 mm glass,
fixed element 10 – 12 mm glass
Set 5.1 / Set 5.2 consisting of: Set 5.1
with single-point fixings
countersunk
Set 5.2
with clamping disc single-point
fixings
Art. No. 29.918
Art. No. 29.919
Art. No. 21.436
Tubular track inclusive end cups,
stock length 3000 mm
Art. No. 21.527
6Clamp fixings
fixing at glass
2Roller carriers CLASSIC
incl. single-point fixings for 8 – 12 mm glass
1 Wall fixing
1 Door stop left hand
1 Door stop right hand
1 Floor guide AGILE
Installation tools
Not covered by the set:
Tubular track inclusive end cups fixed length*
Accessory options for Set 5.1 / Set 5.2
Pull handles / Recessed pull grip
Pull handles
Pair of pull handles
Recessed pull grip Ø 60 mm
Recessed pull grip with grip hole Ø 60 mm
Length   350 mm
Art. No. 29.268
Art. No. 21.240
Length   720 mm
Art. No. 29.271
Art. No. 21.241
Length 1240 mm
Art. No. 29.274
Art. No. 21.242
Length 1760 mm
Art. No. 29.277
Art. No. 21.243
Length   350 mm
Art. No. 21.267
Length   720 mm
Art. No. 21.270
Length 1240 mm
Art. No. 21.273
Length 1760 mm
Art. No. 21.276
for 8/10/12 mm glass
Art. No. 21.291
for 8 mm glass
Art. No. 21.292
for 10 mm glass
Art. No. 21.293
for 12 mm glass
Art. No. 21.294
Door knob back-to-back
for 8 – 12 mm glass
Art. No. 21.423
Door knob one side fixing
for 8 – 12 mm glass
Art. No. 21.422
Art. No. 21.426
Corner lock
Corner lock
Art. No. 21.448
Corner lock with rose on one lock side
Art. No. 29.449
Profile cylinder for corner lock 21.448/449
Art. No. 14.206
Eccentric bushing for corner lock 21.448/449
Art. No. 05.194
Art. No. 21.432
Art. No. 21.430
Further accessories
Aluminium guide rail with brush seals
stock length 3000 mm
stock length 6000 mm
Ceiling connector (bearing function)
Art. No. 29.337
Assembling tool for MANET single-point fixing
Art. No. 29.338
Art. No. 21.134
* When ordering please indicate the necessary length! For calculation please see adjoining page
DORMA
59
manet COMPACT SETS
SET 6.1/6.2
—
Sliding door MANET COMPACT for installation at glass, sidelights on both sides,
for sliding door 8 – 12 mm glass,
fixed element 10 – 12 mm glass
Set 6.1
with countersunk single-point
fixings
Set 6.2
with clamping disc single-point
fixing
Gap 3 mm
Gap 3 mm
min. 110
OB = LM – 6 mm
SB min. = LM – 20 mm
Fixed length: LL = 2 * TB – 80 mm
100
50
50
Sidelight
50
Overpanel
X
Y
Sidelight
Y
143
60
X
143
143
70
Door height max. 2500 mm
Sliding door
Door weight 100 kg
Door height max. 2500 mm
Door width max. 1200 mm
TSG 8/10/12 mm glass thickness
40
40
DBG = LM – 100 mm
LM
TB = LM + 80 mm
For the requisite glass preparation please see pages 20 – 21
60
DORMA
TSG 10/12 mm glass thickness
LM
=Daylight opening
TB
=Door width
DGB =Entry width
OB
=Overpanel width
SBmin.= min. Seitenteilbreite
LL
=Tubular track length
X
=Centre distance
between single-point
fixings overpanel
(OB – 150) * 1/2
Y
=Centre distance
between single-point
fixings sidelight
Y = X – 29
manet COMPACT SETS
Sliding door MANET COMPACT for installation at glass, sidelight on both sides,
for sliding door 8 – 12 mm glass,
fixed elements 10 – 12 mm glass
Set 6.1 / Set 6.2 consisting of: Set 6.1
with single-point fixings
countersunk
Set 6.2
with clamping disc single-point
fixings
Art. No. 29.920
Art. No. 29.921
Art. No. 21.436
Tubular track inclusive end cups,
stock length 3000 mm
Art. No. 21.527
7Clamp fixings
fixing at glass
2Roller carriers CLASSIC
incl. single-point fixings for 8 – 12 mm glass
1 Door stop left hand
1 Door stop right hand
1 Floor guide AGILE
Installation tools
Not covered by the set:
Tubular track inclusive end cups fixed length*
Accessory options for Set 6.1 / Set 6.2
Pull handles / Recessed pull grip
Pull handles
Pair of pull handles
Length   350 mm
Art. No. 29.268
Art. No. 21.240
Length   720 mm
Art. No. 29.271
Art. No. 21.241
Length 1240 mm
Art. No. 29.274
Art. No. 21.242
Length 1760 mm
Art. No. 29.277
Art. No. 21.243
Length   350 mm
Art. No. 21.267
Length   720 mm
Art. No. 21.270
Length 1240 mm
Art. No. 21.273
Length 1760 mm
Art. No. 21.276
Recessed pull grip Ø 60 mm
for 8/10/12 mm glass
Art. No. 21.291
Recessed pull grip with grip hole Ø 60 mm
for 8 mm glass
Art. No. 21.292
for 10 mm glass
Art. No. 21.293
for 12 mm glass
Art. No. 21.294
Door knob back-to-back
for 8 – 12 mm glass
Art. No. 21.423
Door knob one side fixing
for 8 – 12 mm glass
Art. No. 21.422
Art. No. 21.426
Corner lock
Corner lock
Art. No. 21.448
Corner lock with rose on one lock side
Art. No. 29.449
Profile cylinder for corner lock 21.448/449
Art. No. 14.206
Eccentric bushing for corner lock 21.448/449
Art. No. 05.194
Art. No. 21.432
Art. No. 21.430
Further accessories
Aluminium guide rail with brush seals
stock length 3000 mm
stock length 6000 mm
Ceiling connector (bearing function)
Art. No. 29.337
Assembling tool for MANET single-point fixing
Art. No. 29.338
Art. No. 21.134
* When ordering please indicate the necessary length! For calculation please see adjoining page
DORMA
61
PULL HANDLES aND
RECESSED PULL GRIP PROGRAM
—
Accessories
62 – 71
62
DORMA
DORMA
63
manet ACCESSORIES
PULL HANDLES, DOOR KNOBS AND Recessed pull grip
—
The pull handle/knob system is
designed for glass of 8, 10 and
12 mm thickness.
The pull handles can be fixed to
both sliding and pivoting (swing)
doors on one face using the
appropriate connectors or on
both faces by through-bolting
(back-to-back arrangement).
The single-point fixings and
through bolts are included as
standard equipment in the
scope of supply.
The pull handles can be fitted
horizontally, vertically or in a
handrail arrangement.
64
DORMA
manet ACCESSORIES
PULL HANDLES SINGLE
—
Pull handles with single-point
fixings, countersunk
for 8/10/12 mm glass
Pull handle 350 mm
with 2 fixings
Art. No. 29.268
AISI 316L
Art. No. 29.269
Pull handle 720 mm
with 2 fixings
Art. No. 29.271
AISI 316L
Art. No. 29.272
Pull handle 1240 mm
with 3 fixings
Art. No. 29.274
AISI 316L
Art. No. 29.275
Pull handle 1760 mm
with 4 fixings
Art. No. 29.277
AISI 316L
Art. No. 29.278
Pull handles with single-point
fixings, clamping disc
for 8/10/12 mm glass
Pull handle 350 mm
with 2 fixings
Art. No. 21.240
Pull handle 720 mm
with 2 fixings
Art. No. 21.241
AISI 316L
Art. No. 21.281
Pull handle 1240 mm
with 3 fixings
Art. No. 21.242
Pull handle 1760 mm
with 4 fixings
Art. No. 21.243
AISI 316L
Art. No. 21.283
Complete with
single-point fixings
1760
520
520
350
ø 25
150
45
720
520
ø 32
1240
ø 16
Glass thickness
DORMA
65
manet ACCESSORIES
PAIR OF PULL HANDLES
—
Pair of pull handles
incl. connecting bolt
for 8/10/12 mm glass
Pair of pull handles 350 mm
with 2 fixings
Art. No. 21.267
AISI 316L
Art. No. 21.247
Pair of pull handles 720 mm
with 2 fixings
Art. No. 21.270
AISI 316L
Art. No. 21.250
Pair of pull handles 1240 mm
with 3 fixings
Art. No. 21.273
AISI 316L
Art. No. 21.253
Pair of pull handles 1760 mm
with 4 fixings
Art. No. 21.276
AISI 316L
Art. No. 21.256
Complete incl.
connecting bolt
Glass
thickness
40
1225
900
25
20
42
66
DORMA
42
25
Lockable back-to-back
handle bar,
for 6 – 16 mm glass
1225 mm,
with 2 fixings,
complete with closing device
and cylinder
1760
520
720
520
520
ø 25
350
70
45
150
ø 25
1240
ø 16
Glass thickness
Art. No. 21.279
manet ACCESSORIES
door knobs
—
ø 25
ø 32
Glass thickness
51
ø 25
Glass thickness
51
Single-point fixing
clamping disc
51
Door knob one side fixing
for 8/10/12 mm glass
Door knob with single-point
fixing, countersunk
Art. No. 21.422
Door knob with single-point
fixings, clamping disc
Art. No. 21.426
Door knob back-to-back
for 8/10/12 mm glass
Art. No. 21.423
Single-point fixing
countersunk
Spacing adjustment for pull handles and door knobs
—
Conversion set 1 for glass doors,
pair of pull handles/
knob back-to-back
door thickness 13.5 – 21.5 mm
Distance washer
2 mm
Glass doors
Door thickness 13.5 mm:
without distance washer
Door thickness 15 mm:
with 1 distance washer
Door thickness 17.5 mm:
with 2 distance washer
Door thickness 19 mm:
with 3 distance washer
Door thickness 21.5 mm:
with 4 distance washer
Conversion set 2 for timber doors,
pair of pull handles /
knob back-to-back
door thickness 20 – 40 mm
Distance washer
5 mm
Art. No. 21.285
Art. No. 21.286
Timber doors
Door thickness 20 mm:
without distance washer
Door thickness 25 mm:
with 1 distance washer
Door thickness 30 mm:
with 2 distance washer
Door thickness 35 mm:
with 3 distance washer
Door thickness 40 mm:
with 4 distance washer
DORMA
67
manet ACCESSORIES
Spacing adjustment for pull handles and door knobs
—
Conversion set 3
for glass / timber doors,
pull handle / knob single-sided,
single-point fixing
door thickness 15 – 40 mm
countersunk
clamping disc
Art. No. 21.287
Art. No. 21.288
Glass doors / timber doors
Door thickness 15 – 21.5 mm:
Cylinder head screw M6x25
Door thickness 25 – 30 mm:
Cylinder head screw M6x35
Door thickness 35 – 40 mm:
Cylinder head screw M6x50
Conversion set 4
Recessed pull grip
for glass doors
Art. No. 21.295
for timber doors
Art. No. 21.296
Glass doors
Door thickness 13.5 mm:
Grub screw 20 mm
Door thickness 15 mm:
Grub screw 22 mm
Door thickness 17.5 mm:
Grub screw 24 mm
Door thickness 19 mm:
Grub screw 25 mm
Door thickness 21.5 mm:
Grub screw 28 mm
Timber doors
Door thickness 20 mm:
Grub screw 24 mm
Door thickness 25 mm:
Grub screw 28 mm
Door thickness 30 mm:
Grub screw 33 mm
Door thickness 35 mm:
Grub screw 38 mm
Door thickness 40 mm:
Grub screw 43 mm
68
DORMA
manet ACCESSORIES
Recessed pull grip und ARCOS pull handle
—
Grub screw
Recessed pull grip
Ø 50 mm
for 8/10/12 mm glass
Art. No. 21.290
Recessed pull grip
Ø 60 mm
for 8/10/12 mm glass
Art. No. 21.291
Recessed pull grip with grip hole
Ø 60 mm
for 8 mm glass
Art. No. 21.292
for 10 mm glass
Art. No. 21.293
for 12 mm glass
Art. No. 21.294
ARCOS pair of pull handle
for 8/10/12 mm glass
incl. connecting bolt
only in AISI 316L
Bushing
Connecting
bolt
Pull handle 350 mm
with 2 fixings
Art. No. 26.500
Pull handle 750 mm
with 2 fixings
Art. No. 26.510
DORMA
69
manet ACCESsORIES
GLASS PREPARATION FOR PULL HANDLES AND DOOR KNOBS
—
Countersunk bore
on pull handle and door knob,
one side fixing
min. ca. 65 mm
3 -0,2
+0,2
90°
Glass
thickness
1560 mm
±0,3
150 mm
1040 mm
±0,3
±0,3
ø 32
ø 26
520 mm
±0,3
min. ca. 65 mm
Cylindrical bore
on pair of pull handles
and door knobs,
back-to-back
ø 22
at length of pull handles
350 mm
Glass thickness
Cylindrical bore
9
9
80
ø 16
Cylindrical bore
ø 16
398 / 824 mm
Glass thickness
3
Glass thickness
750 / 350 mm drill hole centres distance
20
Cylindrical bore
~65
ø 38
ø 50
85
Glass thickness
70
DORMA
ø 50
ø 60
Glass thickness
Glass thickness
Glass thickness
manet ACCESsORIES
accessories / Installation tools
—
Assembling tool for
MANET Single-point fixing
Art. No. 21.134
Clip-on cover for
single-point fixing
with spring,
5 pieces
Art. No. 29.217
Assembling tool for
MANET single-point fixing
(can also be used as attachment
for torque wrench)
Art. No. 21.137
Sample case
Art. No. 21.995
DORMA
71
manet GENERAL
PLANning tools
—
For planning of intelligent glass solutions we offer you
several planning tools which allow you to create secure
and professional solutions for any kinds of glass doors
and toughend glass assemblies.
The planning tools MANET COMPACT enable you to prepare designs
quickly, reliably and professionally. The software provides you
with all necessary documentation such as dimensioned technical
drawings, glass sizes and preparation measures.
Your benefits:
Easy to operate
Professional and error-free preparation of offers
Rapid response to incoming requests for quotations
Highly reduced planning costs for time and money savings
..
..
..
..
Safety-related information
—
Important safety-related information for the mounting and use of
DORMA glass fittings
(Follow these instructions in addition to the mounting and operating
instructions in order to avoid damage of product and damage to
­person or property.)
Important: All users have to be informed about relevant points
­mentioned in these safety-related information and the mounting and
operating instructions!
General information
1. DORMA recommends using TSG-H (heat soaked toughened safety
glass) to DIN EN 12150-1.
2. DORMA glass fittings are not suitable for application in rooms
where chemicals (e. g. chlorine) are used such as indoor swimming pools, saunas or salt-water pools.
3. Never move sliding panels faster than walking speed
and always stop the door manually before it reaches end position.
4. Do not shut swing doors with excessive force. Install door stop to
prevent door from opening too far.
Mounting
1. Only properly qualified and specially trained staff is authorised to
mount DORMA glass fittings.
2. Never use glass with conchoidal fractures and/or damaged edges.
3. Due to crushing hazards – among others in the area of the
­secondary closing edge – and possible injury caused by breakage
of glass during mounting, corresponding protective clothing
­(especially gloves and protective goggles) is required.
4. C
lean clamping area with fat solvent (standard commercial
­cleaning agent) before mounting the glass fitting.
5. N
ever use clamping shoes on structured glass surfaces (except ­
on satined glass) or glass of heavily varying thickness unless with
a corresponding levelling layer.
6. Never use clamping shoes on self-cleaning coatings.
7. When adjusting glass elements, always stick to the required
­clearance for the respective fitting. Adjust clearance so that the
glass does not touch hart components such as glass, metal or
concrete.
8. Make sure not to use excessive force when installing the glass
(avoid local stress resulting from very tight screws).
Maintenance
Check fittings at regular intervals for proper positioning and smooth
running and door for correct adjustment. Especially highly-­
frequented door systems require inspection by properly qualified
staff (specialised companies or installation firms). Immediately
replace damaged class elements (no glass flaking and/or conchoidal
fractures)!
Subject to change without notice.
For practical planning, please use our drawings DORMA-Glas
DETAIL.
72
DORMA
DORMA
73
74
DORMA
DORMA
75
DORMA-Glas GmbH
Max-Planck-straße 33–45
32107 BAD sAlzuFlEn
GERMAny
Phone +49 5222 924-100
Fax
+49 5222 924-3100
www.dorma.com
WN 05415051532 · 04/13 · GB · XX · x · xx/13
DORMA GmbH + Co. KG
DORMA Platz 1
58256 EnnEPEtAl
GERMAny
Phone +49 2333 793-0
Fax
+49 2333 793-4950
www.dorma.com